[Bf-docboard-svn] bf-manual: [9004] trunk/blender_docs/manual/grease_pencil/modifiers/generate: Merge branch 'blender-3.1-release'

[Aaron Carlisle]

Revision: 9004
          https://developer.blender.org/rBM9004
Author:   Blendify
Date:     2022-02-24 00:50:23 +0100 (Thu, 24 Feb 2022)
Log Message:
-----------
Merge branch 'blender-3.1-release'

Modified Paths:
--------------
    trunk/blender_docs/manual/grease_pencil/modifiers/deform/shrinkwrap.rst
    trunk/blender_docs/manual/grease_pencil/modifiers/generate/length.rst
    trunk/blender_docs/manual/grease_pencil/modifiers/generate/line_art.rst

Property Changed:
----------------
    trunk/blender_docs/

Index: trunk/blender_docs
===================================================================
--- trunk/blender_docs	2022-02-23 23:46:57 UTC (rev 9003)
+++ trunk/blender_docs	2022-02-23 23:50:23 UTC (rev 9004)

Property changes on: trunk/blender_docs
___________________________________________________________________
Modified: svn:mergeinfo
## -1,4 +1,4 ##
 /branches/blender-2.92-release/blender_docs:7610-7921
 /branches/blender-2.93-release/blender_docs:7959-8113
 /branches/blender-3.0-release/blender_docs:8543-8943
-/branches/blender-3.1-release/blender_docs:8904-8997
\ No newline at end of property
+/branches/blender-3.1-release/blender_docs:8904-9003
\ No newline at end of property
Modified: trunk/blender_docs/manual/grease_pencil/modifiers/deform/shrinkwrap.rst
===================================================================
--- trunk/blender_docs/manual/grease_pencil/modifiers/deform/shrinkwrap.rst	2022-02-23 23:46:57 UTC (rev 9003)
+++ trunk/blender_docs/manual/grease_pencil/modifiers/deform/shrinkwrap.rst	2022-02-23 23:50:23 UTC (rev 9004)
@@ -129,21 +129,11 @@
 Nearest Vertex
 --------------
 
-.. figure:: /images/grease-pencil_modifiers_deform_shrinkwrap_nearest-vertex.png
-   :align: right
-   :width: 300px
-
-   Nearest Vertex mode.
-
 This will snap vertices to the nearest vertex of the shrunk target. It adds no extra options.
 
 This method doesn't support the *Snap Mode* setting.
 
-.. container:: lead
 
-   .. clear
-
-
 Target Normal Project
 ---------------------
 

Modified: trunk/blender_docs/manual/grease_pencil/modifiers/generate/length.rst
===================================================================
--- trunk/blender_docs/manual/grease_pencil/modifiers/generate/length.rst	2022-02-23 23:46:57 UTC (rev 9003)
+++ trunk/blender_docs/manual/grease_pencil/modifiers/generate/length.rst	2022-02-23 23:50:23 UTC (rev 9004)
@@ -51,6 +51,28 @@
    Invert the curvature of the stroke's extension.
 
 
+Random Offsets
+--------------
+
+Random Offset Start/End
+   Size of random length added to the start/end of each stroke.
+
+Random Noise Offset
+   Smoothly offset each stroke's random value.
+
+Seed
+   Number used to generate different noise patterns.
+
+
+Randomize
+^^^^^^^^^
+
+Re-randomizes values over time.
+
+Step
+   Number of frames before recalculate random values again.
+
+
 Influence Filters
 -----------------
 

Modified: trunk/blender_docs/manual/grease_pencil/modifiers/generate/line_art.rst
===================================================================
--- trunk/blender_docs/manual/grease_pencil/modifiers/generate/line_art.rst	2022-02-23 23:46:57 UTC (rev 9003)
+++ trunk/blender_docs/manual/grease_pencil/modifiers/generate/line_art.rst	2022-02-23 23:50:23 UTC (rev 9004)
@@ -94,7 +94,13 @@
 Crease on Sharp
    Allow creases to show on sharp edges.
 
+.. _bpy.types.LineartGpencilModifier.use_back_face_culling:
 
+Force Backface Culling
+   Remove all back faces to speed up calculation.
+   Note, removing back faces will create edges in different occlusion levels than when disabled.
+
+
 Edge Types
 ----------
 
@@ -223,6 +229,11 @@
 Boundaries
    Filter feature lines based on face mark boundaries.
 
+.. _bpy.types.LineartGpencilModifier.use_face_mark_keep_contour:
+
+Keep Contour
+   Preserve contour lines while filtering.
+
 .. figure:: /images/grease-pencil_modifiers_generate_line-art_face-mark-filtering-example.png
 
 
@@ -253,6 +264,10 @@
    Loose as Contour
       Edges that do not form a face will be classified as contour lines.
 
+   Preserve Details
+      Instead of splitting at each occlusion change, keep small details from the initial chain.
+      When details are not kept, will create a much smoother result.
+
    Geometry Space
       Use geometry distance for chaining instead of image space.